Inlines
Skating Guide

1. Things to consider before putting on your Inline Skates:

So now you have your skates. You just opened the box to your new Impala Inline Skates, first thing is to check through your skates before each use.


★ Move each wheel to check axle tightness. Being careful to check the screws/bolts that secure the wheels to make sure they are tight.

★ If they are too loose, tighten them with the allen wrenches.

★ Have a look at your skates and check for any cracks, if you do find a crack, do not use your skates and have the skates replaced immediately.

★ It is recommended that children skate under adult supervision at all times.

★ To ensure maximum ankle support, make sure you have laced your skates all the way up, and that the buckle is firmly fastened.

★ If you notice movement of your feet in the skates, you should adjust the laces and buckles.

★ Wear protective gear - helmet, wrist guards, elbow and kneepads.

★ It is recommended to take lessons to learn the basics of skating, or seek advice from an experienced skater before skating in busy, high-traffic areas.

★ Always observe road rules and avoid high-traffic areas.

  • 2. Starting Out

    If this is your first time skating, it is recommended to practice on a smooth
    surface. Start out on a flat area (no hills!).

    -

    ★ Use a nearby wall to help you get to your feet. Practice on carpet or grass
    before you move to concrete or harder surfaces.

    ★ If there’s nothing around to use for assistance to stand up, pull one foot up
    under you and place both hands on the ground in front of you.

    ★ While skating, you should not overestimate your own skills, always take it
    slow at first.

  • 3. Practice different movements. (Leaning, pivoting, and crouching)

    Practicing these movements will help you get used to the kinds of methods
    you’ll be using later to gain speed and move around.

    -

    ★ It may not feel easy at first, but over time, you will start to feel more confident.

    ★ Ensure to bend your knees and keep your center of gravity a little lower than
    when you’re walking.

  • 4. Get Moving & Start Moving Slowly.

    By now, you will comfortable in your skates and standing up. When you feel confident enough, find some flat ground with plenty of room to move
    around.

    -

    ★ Stand with feet shoulder width apart and bend your knees slightly. Gently
    push off the back foot as you glide forward on the other skate.

    ★ Then bring your back skate forward so it is even with your front skate and
    repeat on the other side keeping your knees slightly bent.

    ★ Learning to skate will take some getting used to, and keep in mind that falling
    is a part of learning and not a sign of failure.

    ★ Pick up one foot and set it down in front of the other. Then repeat with the
    other foot.

    ★ Take really small steps at first and avoid

  • 5. Turn your steps into smooth strokes.

    Continue putting one foot in front of the other, only now rather than dropping
    your foot straight down, push it forward and out.

    -

    ★ Lift your skates just enough to set them down for the next stroke, letting your
    momentum carry you forward.

  • 6. Practice Braking.

    Impala Inline skates come with a brake included in the box, which is designed
    to stop you slowly. Please keep in mind, this does not provide an immediate
    stop.

    -

    ★ It is highly recommended to put the brake on the skate when starting out.

    ★ After attaching the brake, while moving lean forward slightly, bring your legs
    close together, shift the right leg forward (assuming your brake is on your
    right skate) ahead of the left leg, lift the toe of the skate with the brake, put
    pressure on the rear part of the cuff and brake with your heel.

    ★ The firmer you press down with your heel, the more effective the stopping
    power will be.

    ★ Be sure to keep your eyes on the road, and begin braking with enough time to stop.

    ★ Make sure you know how to control your speed and stop before skating on
    any inclined surfaces.

1 5

ADVANVED TIP

Rockered Wheels

To adjust to rockered alignment:

1. Unscrew the axle bolts and remove the wheels. Once removed, you will see the metal spacer, which is inserted into the chassis.

2. Flipping the position of the spacers will lower the height of the two middle wheels into the “rocker” alignment position.

  • Flat alignment.

    Your skates come with all four heels assembled in straight, or “flat” alignment. This means all four wheels on each skate are touching the ground at all times.

    -

    Best for: beginners, max speed.

  • Rockered alignment.

    This is when the wheels are adjusted and only some of the wheels - usually the ones in the middle - are closer to the ground. Doing this increases maneuverability, making turning easier.

    -

    Best for: slalom, hockey, artistic or aggressive skating

FAQ

How do I install the brake?

Your skates come with a brake, included in the box. Here’s how you install it:

1. Decide which foot you prefer to brake with, usually this will be your stronger leg.

2. Use the included skate tool and allen wrench to remove the rear nut and axle from the chassis.

3. Grab the brake from your skate box and position it so the holes line up to the chassis where you just removed the axle from. Make sure the upper groove catches the latch inside the chassis. The brake should not move up and down if properly connected.

4. Remove longer axle and bolt from your skate box (this should come assembled inserted in brake unit already).

5. Place longer axle through the holes in the brake and through the chassis, securing brake and rear wheel in place.

6. Tighten brake and wheel assembly to chassis using the skate tool and allen wrench. Screw until tight.

7. Ensure brake is secured tightly before use. There should be no movement in the brake at all. Done!

How can I keep my skates clean?

The liners can be removed from the skate to be washed and air-dried.

1. Set the washing machine to 30° C (85° F) 2. Do not use strong detergent, softeners, or solvents.

3. Once you wash you can air-dry liners. Do not tumble dry.

4. Be careful to keep away from any type of heat source.

5. Maintaining your equipment in good condition increases safety and ensures its longer life.

6. The liners are breathable, comfortable and are

How do I remove wheels?

1. Unscrew with allen wrenches (included in box).

2. Remove axle.

How do I assemble my wheels?

1. Reinsert the axle.

2. Re-tighten bolts securely

How can I clean my wheels and rubber shield bearings?

How can I clean my wheels and rubber shield bearings?

If the wheels and bearings aren’t spinning freely, you may need to clean them. For cleaning the wheels, you will need a cleaning cloth. For bearings, you will need lubricant.

1. Take out all 4 wheels with Allen wrenches.

2. Wipe off the dirt from the wheels.

3. Clean off axles.

4. Clean the inside of the frame with a cloth.

5. Remove bearings from the wheels, with a safety pin, take off the rubber covers or shields from the bearings.

6. Wipe off the grime. Avoid using water, this will rust the bearings

7. Apply two drops of lubricant to each and put shields back on

8. Be sure to put spacer back between bearings before putting the wheels back in the frame.

9. Use one small drop of blue (removable) thread lock

WARNING:

★ Check the wear limit line on your Brake. Brake pads should be replaced once the wear limit line is reached otherwise you risk the loss of braking force, the loss of control, and consequent injury.

★ If you decide to skate without a brake, you do so at your own risk.

★ It is forbidden to make any changes or modifications which could impair essential features of the Inline Skates as this affects the safety of the user.

★ Mechanical damage occurred during the use at fault of the customer, such as scratches or cracks of shoes, damaged blades and ripped laces etc. do not giverise to a complaint.